| Previous | Table of Contents | Next |
The mail program, like most e-mail programs, allows you to create an alias for an address and a group alias for a list of addresses. You can treat the group alias as a mailing list. Using an alias for an individual address is easier than using the regular address because the alias is typically shorter and easier to remember.
To set an individual or group alias for one mail session, you use the alias command at the ? prompt while you’re reading your e-mail. To make the aliases more useful, put the aliases in a file named .mailrc in your home directory (as described in the following section).
The following is an example of setting and using aliases with the mail program:
mail Type ? for help.
“/var/spool/mail/bkorn”: 5 messages 2 new 1 unread
1 sarah Wed Jan 5 09:17 15/363
2 [email protected] Thu Jan 6 10:18 26/657 Meeting on
Friday
U 3 wjones Fri Jan 7 08:09 32/900 Framistan Order
> N 4 chendric Fri Jan 7 13:22 35/1347 Draft Report
N 5 [email protected] Sat Jan 8 13:21 76/3103 Excerpt from GREAT
new Linux
?
alias ros [email protected]
To set up a group alias, use the alias command followed by the alias for the addresses. The following creates an alias called friends and then forwards some mail to the group:
alias friends chendric karlack abc.com!homebase!fran [email protected] m friends Subject: Excerpts from new Linux book - get a copy! ~f 5 Interpolating: 5 ~. EOT ?
You can customize your mail environment by putting commands or set-environment variables in the .mailrc file in your home directory. The mail program checks that file whenever you use the program. You can set quite a few environment variables and commands in .mailrc, and different mail programs will use different commands. Check your man page for your mail program for a list of all the .mailrc options. Some of the commands mail recognizes are given earlier in the section “Getting Help with mail”; this section describes a subset of the commands and variables that can be used in the .mailrc file. Table 33.1 lists these commands; Table 33.2 lists the environment variables.
| Command | Definition |
|---|---|
| # | Denotes a comment. No action is taken. |
| alias | Sets an individual or group alias. Used as alias alias-name address-list. |
| set | Sets an environment variable. Used as set variable-name or set variable-name=string. |
TIP: You can issue any of the commands in Table 33.1 from the ? prompt anytime you use mail; they’ll be active only for that session.
| Variable | Definition |
|---|---|
| askcc | Prompts for the cc: list after the message is entered. Default is noaskcc. |
| asksub | Prompts for the Subject list before the message is entered. Enabled by default. |
| noheader | Doesn’t print header information on available messages when you start mail. Disabled by default. |
| ignore | Ignores interrupt characters when you enter messages. Useful if you have a “noisy” connection over some telephone or other communication lines. Default is noignore. |
| metoo | When you have your name in a group alias, a message normally isn’t sent to you. Setting this variable allows you to receive messages sent to a group alias that contains your address. Default is nometoo. |
TIP: You can set a system-wide environment by putting the commands or set variables in the /etc/mail.rc file.
The following example sets up the .mailrc file so that you use the commands and environment variables listed in Tables 33.1 and 33.2. The pound sign (#) is used to document the work. You can create this file by using vi or any other editor that can produce a text or ASCII file.
# .mailrc file for D. Wayne Love # make sure interrupts are NOT ignored set noignore # set variables so that prompts for Subject and Cc always appear set asksub set askcc # individual aliases alias billy wcuth alias ben [email protected] alias me dwlove # group aliases, mailing list alias mercs [email protected] quinn taura alias research jones brown smith alias googol djames bkorn [email protected] bkorn
Place these statements in the .mailrc file. Now whenever you start mail, these command statements are processed.
As you read e-mail in a mailbox, you can read, skip, or delete messages. (You learn about deleting messages later in this chapter.) These actions don’t take place in the mailbox itself, but in a temporary copy of the mailbox. You can quit the e-mail program so that your mailbox is changed by your actions (the modified temporary copy replaces the original mailbox), or you can quit so that your mailbox is unchanged regardless of what you did during your e-mail session.
| Previous | Table of Contents | Next |